YUKIWA SEIKO INC Japan
Cost Reduction
Increase the number of machining per one tool!
Product Feature
It is possible to increase the number of machining per one tool by using a toolholder of high accuracy. Increased number of machining per one tool contributes reduction in machining cost.
Cost Reduction
Cycle time can be reduced!
Product Feature
Rigidity of a toolholder greatly influences surface roughness of the workpiece. There is no probrem with the surface roughness of the workpiece, the cycle time can be reduced by increasing the feed rate.
Cost Reduction
Increase the number of machining per one tool!
Product Feature
As Super G1 Chuck has high gripping force, it fully extracts the performance of the tool and the machine. High gripping force stabilize the runout accuracy of the tool and contributes reduction in machining cost.
Proposal of a new processing method
Milling Chuck is unnecessary!
Product Feature
Although it tends to seem that end mill is held by Milling Chuck, it is not enough as rigidity that Milling Chuck has just high holding power. Super G1 Chuck is a high rigidity tool holder strong against horizontal influence.
Proposal of a new processing method
Check the difference of processing sound!
Product Feature
Milling Chuck has high gripping force, but the rigidity is low. As a result, the tool inclines to the side and makes a high-pitched cutting sound. Super G1 Chuck inclines less frequently and keeps the cutting sound very quiet due to its high rigidity even when cutting load is applied in the lateral direction.
Cost Reduction
Feeding rate of milling was doubled!
Product Feature
Milling Chuck has high gripping force, but the rigidity is low. As a result, the tool inclines to the side and makes a high-pitched cutting sound. Super G1 Chuck inclines less frequently and keeps the cutting sound very quiet due to its high rigidity even when cutting load is applied in the lateral direction.
Cost Reduction
It can be made end mill feed rate fast!
Product Feature
Green G1 chuck makes it possible to change the feed speed fast at the end mill processing. Cycle time is shortened and it contributes to improvement your productivity.
Cost Reduction
Economic holder that can be cut fine and quickly
Product Feature
Milling Chuck has high gripping force, but the rigidity is low. As a result, the tool inclines to the side and makes a high-pitched cutting sound. Green G1 Chuck inclines less frequently and keeps the cutting sound very quiet due to its high rigidity even when cutting load is applied in the lateral direction.
Improvement of quality
The surface roughness of work will be
Product Feature
Milling Chuck has high gripping force, but the rigidity is low. As a result, the tool inclines to the side and makes a high-pitched cutting sound. Green G1 Chuck inclines less frequently and keeps the cutting sound very quiet due to its high rigidity even when cutting load is applied in the lateral direction.
Cost Reduction
Increase the number of machining per
Product Feature
Yukiwa Seiko's Tool Holder Green G1 chuck maintains high runout accuracy even when the machining center rotates at high speeds, which prevents wear on the cutting tool and improves the work surface roughness.
Proposal of a new processing method
Cutting using the center through coolant.
Product Feature
It's a cutting using the center through coolant. The center through coolant collet is most suitable for chucking oil hole drills. Side through coolant collet supplies a coolant in a pinpoint to the processing part.
Proposal of a new processing method
Collet holder for small dia of φ4mm or less
Product Feature
Smart chuck is most suitable for processing by tools less than 4mm. Since the nut outer diameter is 12mm, it reduces the interference to the work and jigs. We will guarantee a runout accuracy 5μm in a state of being set in the holder as the same as Super G1 Chuck.
Cost Reduction
The accuracy makes tool expenses reduce!
Product Feature
Super G1 Chuck has guaranteed the comprehensive run-out accuracy in the state where the collet was set. Moreover, it set to the system and is very stable also about dynamic run-out accuracy, and there is little wear of tool and it can perform reduction of tool expenses.
Proposal of a new processing method
It can be made the machine space small!
Product Feature
YHL flange type clamp set is a special-purpose machine without the turret and ATC of NC lathe, and is the unit which can carry out manual exchange of the HSK holder easily.
Cost Reduction
|
Cost Reduction
|
Cost Reduction
|
Proposal of a new processing method
|
Proposal of a new processing method
|
Proposal of a new processing method
|